Start with the quilt top and the fabric you can actually use
This page starts with the crib preset, a 36 × 52-inch quilt top. It compares backing cut from 42-inch and 108-inch usable fabric widths using four inches beyond each quilt edge and half-inch seam allowances on the joining pieces. Use the table to see the two width choices before buying fabric. Then adjust the inputs above to match your top and your quilter’s required margins. The printed cutting card records the current inputs and direction, rather than silently using the starting example.
The preset name is only a convenient measurement label. Measure the finished top after its borders are attached. A pattern, mattress label or nominal fabric width is not a substitute for that measurement. WOF here means fabric you can use after removing selvages. If the bolt’s advertised width is larger than the usable width, enter the usable value; the general backing calculator accepts a measured width when these two presets are not suitable.
The backing constraint for this crib size
A crib preset here means a 36 × 52-inch quilt top. It is a measurement shortcut, not a universal crib or bedding standard. With four inches beyond every edge, the backing area becomes 44 × 60. That small 44-inch width already exceeds a usable 42-inch fabric width, so one narrow panel will not cover it. Two vertical panels are needed even though the original quilt top was narrower than the fabric.
On usable 108-inch backing, one panel covers either orientation. Cutting a 44-inch length across the wide fabric uses less purchased length than cutting 60 inches. That comparison only works if you are comfortable turning the print. Check its direction before choosing the lower-yardage layout; a directional motif may justify buying the longer cut.
Follow the actual narrow-fabric panel calculation
With the default margins, the backing must cover 44 × 60 inches. In the vertical-seam layout, the engine needs 2 panels, each 42 inches wide by 60 inches long. Their total cut length is 120 inches. Dividing by 36 gives 3.3333 yards, and rounding upward to the next eighth gives a purchase estimate of 3.375 yards. The joined width is 83 inches after allowances at all joins.
The horizontal layout needs 2 panels, each 42 inches wide by 44 inches long, and rounds to 2.5 yards. Compare those total quantities rather than selecting the direction with the shorter individual panel. Two seams consume more width than one, and an extra panel can outweigh a shorter cut. The same calculation is repeated independently for the 108-inch option shown in the table.
Understand what a seam removes
A join uses an allowance on both fabric pieces. With a half-inch allowance, each joined seam consumes one inch from the combined usable widths. The assembled width is n × WOF minus 2 × seam allowance × (n − 1). One panel has no joining loss; two have one join; three have two. This is why multiplying a fabric width by a panel count without subtracting the joins can leave the backing short.
Panel count increases in whole steps. Reducing the required width slightly may leave the count unchanged; crossing the usable assembled width requires another entire panel. The tool compares two simple full-width layouts, with vertical or horizontal seams relative to the quilt top. It does not nest scraps, calculate diagonal piecing or search all possible arrangements. Choose a quarter-inch backing seam only when your quilter permits it, and keep the same seam allowance on the card and at the machine.
Compare the wide backing without assuming it is seamless
At a genuinely usable 108-inch width, the vertical layout needs 1 panel(s) and 1.75 purchased yards. The horizontal layout needs 1 panel(s) and 1.25 purchased yards. These results depend on the enlarged backing area, not just the dimensions of the top. Check the table’s joined width against the required dimension before deciding whether a single panel is sufficient.
A lower yardage does not by itself choose the fabric. The calculation has no price, print-repeat, shrinkage or stock information. A fabric design might need to run in one direction or need extra length for matching. If your quilter asks for a wider margin, increase the margin and recalculate rather than trimming the original top or treating the side allowance as optional. Confirm fabric availability and the actual cut before turning this plan into a purchase.
Cut, join and check in that order
Write the panel count, usable width and individual cut length on the printed card. Lay out the fabric and mark the intended top of the print before cutting. Remove unusable edges and check the width again. Cut the required full-width panel lengths, join them with the selected allowance, then measure the assembled backing. Place the quilt top centrally on it and check that the requested extra fabric remains on all four sides.
Keep the card with the quilt until the backing is accepted by your quilter. If the top grows after another border or the backing shrinks after washing, update the measured inputs and print a replacement. The calculator cannot determine a shrinkage percentage from a fabric label. Add any shrinkage, matching and cutting-error allowance separately based on your actual fabric and method; the displayed yardage only covers the panel plan and its upward purchase rounding.
Read excess fabric and purchase rounding separately
The cut-area excess percentage compares the total rectangle area in the cut panels with the required backing area. It includes fabric consumed at joins and material available for trimming. It is not a defect rate, savings promise or measure of how much can be reclaimed. A wide layout can use fewer yards but have more area excess because each yard is wider. Keep those two measures separate when comparing the plans.
Purchase rounding adds enough bolt length to reach the next eighth of a yard. That small length remainder is separate from the cut-area excess calculation. A shop may sell in other increments, so round your actual order to its policy while retaining at least the quantity on the card. This tool produces a cutting specification, not an order, a quilting-service approval or an optimized plan for arbitrary leftovers.
Questions about this backing
Is 36 × 52 the required size for every crib quilt?
No. It is the measurement used by this preset. Your pattern, intended drape and finished top may differ. Replace the width and length with measured top dimensions, then recalculate the margin-inclusive backing before using the cutting card.
What if the fabric is labeled 108 inches but measures narrower?
Use the width remaining after selvages are removed. A small difference can increase the panel count near an exact fit. These pages compare 42 and 108 usable inches; open the main backing calculator for another measured width rather than treating the advertised number as usable fabric.
Can I choose the cheaper orientation automatically?
The tool compares yardage, not prices. Both layouts use whole widths and ignore patterned repeats or shrinking. Check whether the print can turn and whether your quilter accepts the seam placement. A tied yardage result leaves direction as a practical fabric and seam choice.
Does the card include binding or HST fabric?
No. Backing is its own fabric plan. Binding depends on strip width and joining method, and HST fabric depends on the block size, quantity and batch method. Use the separate tools for those tasks so their quantities are not added to or confused with backing yardage.